Engineering Analysis: 70W High-Pressure Sodium to LED Commercial Retrofit
Upgrading 70-watt High-Pressure Sodium fixtures (~92W system draw) to 25–40W LED cuts lighting load by 65%, delivering rapid payback on 12-to-24 hour commercial schedules.
1. Bare-Lamp Rating vs. Delivered LED Lumens (~4,500 lm)
Although a 70W High-Pressure Sodium lamp is rated at 6,400 initial / 5,700 mean bare-lamp lumens, omnidirectional HPS loses 30–40% of that light inside the reflector housing and emits monochromatic ~2100K orange light (CRI ~22) with poor nighttime contrast. A directional white LED (25–40W) delivering roughly 4,500 LM-79 fixture lumens puts broad-spectrum white light (CRI 70–80+) directly onto the target surface.
2. Eliminating Ballast Losses
HID lamps require a ballast (and on HPS/pulse-start MH, an ignitor) to strike and regulate the arc. On a 70W High-Pressure Sodium fixture, ballast losses add roughly 22W (31%), bringing true wall draw to ~92W. Switching to an integrated LED luminaire or Type B ballast-bypass lamp drops meter draw from ~92W to 25–40W.
3. Commercial Facility Savings (12 Hrs/Day at $0.13/kWh)
Operating 12 hours per day, 365 days per year (4,380 hours/yr):
- Per-Lamp / Per-Fixture Savings: Cuts 261 kWh/year, saving $33.88/year per unit.
- 25-Unit Facility Upgrade: Retrofitting 25 units reduces annual utility bills by $846.98/year.
- Reduced Lift & Relamping Labor: High-bay, pole, and canopy fixtures often require scissor-lift or bucket-truck service calls. A 50,000+ hour LED rating eliminates multiple relamping and ballast-replacement cycles.
- Instant Outage Recovery: HPS lamps need ~1 minute to cool before restriking and several minutes to reach full output; LEDs return at 100% brightness immediately.
4. Primary Applications for 70W High-Pressure Sodium Retrofits
Commonly installed in residential streetlights, dusk-to-dawn yard and barn lights, small building wall packs, and entry security lights. Physical lamp specification: ED17 (also BD17 or ED23½) bulb with an E26 medium or E39 mogul base.
Swapping the monochromatic 2100K amber of HPS (CRI ~22) for a directional 25–40W white LED (~4,500 delivered lumens, CRI 70–80+) makes vehicle colors, clothing, and faces identifiable on security cameras while cutting system draw from ~92W to 25–40W.
System draw drops from about 92W (lamp plus ballast) to 25–40W.
Quick Reference: 70W HPS Lamp vs. LED Replacement
| Spec | 70W HPS lamp | LED replacement |
|---|---|---|
| ANSI ballast code | S62 | None (ballast removed / new fixture) |
| Bulb & base | ED17 (also BD17 or ED23½) bulb with an E26 medium or E39 mogul base | Type B corn bulb or integrated LED fixture |
| Light output | 6,400 initial / 5,700 mean bare-lamp lm | ~4,500 delivered lm |
| Power at the meter | ~92W including ballast | 25–40W |
| Color | ~2,000–2,100K amber, CRI ~20–22 | 2700K–5000K white, CRI 70–80+ |
| Rated life | 24,000+ hours | 50,000+ hours (L70), typical |
| Warm-up / restrike | Several minutes warm-up / ~1 min restrike | Instant |
What's Specific to the 70W HPS Retrofit
The medium-base trap
Many 70W HPS lamps use an ordinary-looking E26 medium base, so it is tempting to screw in a household LED bulb. Don't: the fixture contains a ballast and an ignitor that fires starting pulses of several thousand volts, which will destroy a standard LED bulb. Bypass both the ballast and the ignitor before installing a Type B LED, or replace the fixture.
Keep the photocell
Most 70W dusk-to-dawn fixtures switch on with a built-in photocell. After a ballast bypass the photocell still works because it switches line voltage ahead of the ballast. If the light cycles at night, replace the photocell with one rated for electronic LED loads.
Pick 3000K or warmer near homes
The American Medical Association's 2016 street-lighting guidance recommends 3000K or lower outdoors to limit nighttime glare and blue-rich spill light. For yards, driveways, and residential streets, a 2700K–3000K LED avoids harsh blue glare while still restoring true color.
Sizing From Delivered Light (Worked Example)
Omnidirectional 70W HPS lamps lose roughly 30–35% of bare-lamp output inside the reflector housing, and broad-spectrum white LEDs (CRI 70–80+) achieve equivalent outdoor task visibility at lower raw lumens than 2100K amber sodium.
Example: targeting ~4,500 delivered lumens from an integrated LED luminaire operating at 140 lm/W requires roughly 30W — compared with ~92W on the existing 70W HPS ballast circuit. For critical roadways, sports poles, or high-bay aisles, verify spacing with the manufacturer's IES photometric file.
5. Commercial Installation: Type B Ballast-Bypass Protocol
When retrofitting an existing housing with a Type B (ballast-bypass) LED lamp rather than replacing the whole fixture:
- Lock Out Power: Shut off and lock out the branch circuit breaker at the panel, then verify zero voltage at the fixture.
- Bypass the Ballast: Disconnect incoming line and neutral leads from the old ballast (and disconnect any ignitor and capacitor — leaving an HID ignitor in circuit sends multi-kilovolt pulses that will destroy an LED driver).
- Check Sockets & Wire Direct: Connect line voltage (typically 120–277V) to the lamp socket leads per the LED manufacturer's wiring diagram.
- Apply the Retrofit Label: Place the included modification sticker inside the luminaire housing warning future technicians that the ballast has been bypassed and legacy High-Pressure Sodium lamps must not be installed.