Engineering Analysis: 250W High-Pressure Sodium to LED Commercial Retrofit
Upgrading 250-watt High-Pressure Sodium fixtures (~300W system draw) to 90–120W LED cuts lighting load by 65%, delivering rapid payback on 12-to-24 hour commercial schedules.
1. Bare-Lamp Rating vs. Delivered LED Lumens (~15,000 lm)
Although a 250W High-Pressure Sodium lamp is rated at 28,000 initial / 25,000 mean bare-lamp lumens, omnidirectional HPS loses 30–40% of that light inside the reflector housing and emits monochromatic ~2100K orange light (CRI ~22) with poor nighttime contrast. A directional white LED (90–120W) delivering roughly 15,000 LM-79 fixture lumens puts broad-spectrum white light (CRI 70–80+) directly onto the target surface.
2. Eliminating Ballast Losses
HID lamps require a ballast (and on HPS/pulse-start MH, an ignitor) to strike and regulate the arc. On a 250W High-Pressure Sodium fixture, ballast losses add roughly 50W (20%), bringing true wall draw to ~300W. Switching to an integrated LED luminaire or Type B ballast-bypass lamp drops meter draw from ~300W to 90–120W.
3. Commercial Facility Savings (12 Hrs/Day at $0.13/kWh)
Operating 12 hours per day, 365 days per year (4,380 hours/yr):
- Per-Lamp / Per-Fixture Savings: Cuts 854 kWh/year, saving $111.03/year per unit.
- 25-Unit Facility Upgrade: Retrofitting 25 units reduces annual utility bills by $2775.82/year.
- Reduced Lift & Relamping Labor: High-bay, pole, and canopy fixtures often require scissor-lift or bucket-truck service calls. A 50,000+ hour LED rating eliminates multiple relamping and ballast-replacement cycles.
- Instant Outage Recovery: HPS lamps need ~1 minute to cool before restriking and several minutes to reach full output; LEDs return at 100% brightness immediately.
4. Primary Applications for 250W High-Pressure Sodium Retrofits
Commonly installed in arterial roadways, commercial parking lots, farm and equipment yards, rail yards, and older warehouse bays. Physical lamp specification: ED18 bulb with an E39 mogul base.
System draw drops from about 300W to 90–120W (~15,000 delivered white LED lumens), cutting energy consumption by nearly two-thirds while dramatically improving night visibility.
At 250W the magnetic ballast alone wastes roughly 50W continuously; removing it accounts for a major share of the kWh savings.
Quick Reference: 250W HPS Lamp vs. LED Replacement
| Spec | 250W HPS lamp | LED replacement |
|---|---|---|
| ANSI ballast code | S50 | None (ballast removed / new fixture) |
| Bulb & base | ED18 bulb with an E39 mogul base | Type B corn bulb or integrated LED fixture |
| Light output | 28,000 initial / 25,000 mean bare-lamp lm | ~15,000 delivered lm |
| Power at the meter | ~300W including ballast | 90–120W |
| Color | ~2,000–2,100K amber, CRI ~20–22 | 2700K–5000K white, CRI 70–80+ |
| Rated life | 24,000+ hours | 50,000+ hours (L70), typical |
| Warm-up / restrike | Several minutes warm-up / ~1 min restrike | Instant |
What's Specific to the 250W HPS Retrofit
Check the line voltage first
250W HID poles and wall packs are commonly fed at 208, 240, or 277V, and some industrial sites use 480V. Standard commercial LED fixtures accept 120–277V; 347V or 480V circuits require a high-voltage driver version.
Why 90–120W white LED matches 250W orange HPS
Although a bare 250W HPS lamp is rated at 25,000 mean lumens, 30–35% is lost inside the reflector and its 2100K amber spectrum (CRI ~22) gives poor peripheral contrast at night. A directional 90–120W white LED (~15,000 delivered lumens, CRI 70–80+) puts crisp, even light straight onto the pavement.
Measure housing clearance before buying a corn bulb
High-wattage E39 corn bulbs are wider and heavier than slim ED18 HPS tubes. If the housing is cramped or has a yellowed lens, install an integrated 100W LED shoebox or area fixture instead.
Sizing From Delivered Light (Worked Example)
Omnidirectional 250W HPS lamps lose roughly 30–35% of bare-lamp output inside the reflector housing, and broad-spectrum white LEDs (CRI 70–80+) achieve equivalent outdoor task visibility at lower raw lumens than 2100K amber sodium.
Example: targeting ~15,000 delivered lumens from an integrated LED luminaire operating at 140 lm/W requires roughly 105W — compared with ~300W on the existing 250W HPS ballast circuit. For critical roadways, sports poles, or high-bay aisles, verify spacing with the manufacturer's IES photometric file.
5. Commercial Installation: Type B Ballast-Bypass Protocol
When retrofitting an existing housing with a Type B (ballast-bypass) LED lamp rather than replacing the whole fixture:
- Lock Out Power: Shut off and lock out the branch circuit breaker at the panel, then verify zero voltage at the fixture.
- Bypass the Ballast: Disconnect incoming line and neutral leads from the old ballast (and disconnect any ignitor and capacitor — leaving an HID ignitor in circuit sends multi-kilovolt pulses that will destroy an LED driver).
- Check Sockets & Wire Direct: Connect line voltage (typically 120–277V) to the lamp socket leads per the LED manufacturer's wiring diagram.
- Apply the Retrofit Label: Place the included modification sticker inside the luminaire housing warning future technicians that the ballast has been bypassed and legacy High-Pressure Sodium lamps must not be installed.