Engineering Analysis: 150W High-Pressure Sodium to LED Commercial Retrofit
Upgrading 150-watt High-Pressure Sodium fixtures (~190W system draw) to 50–75W LED cuts lighting load by 67%, delivering rapid payback on 12-to-24 hour commercial schedules.
1. Bare-Lamp Rating vs. Delivered LED Lumens (~9,000 lm)
Although a 150W High-Pressure Sodium lamp is rated at 16,000 initial / 14,400 mean bare-lamp lumens, omnidirectional HPS loses 30–40% of that light inside the reflector housing and emits monochromatic ~2100K orange light (CRI ~22) with poor nighttime contrast. A directional white LED (50–75W) delivering roughly 9,000 LM-79 fixture lumens puts broad-spectrum white light (CRI 70–80+) directly onto the target surface.
2. Eliminating Ballast Losses
HID lamps require a ballast (and on HPS/pulse-start MH, an ignitor) to strike and regulate the arc. On a 150W High-Pressure Sodium fixture, ballast losses add roughly 40W (27%), bringing true wall draw to ~190W. Switching to an integrated LED luminaire or Type B ballast-bypass lamp drops meter draw from ~190W to 50–75W.
3. Commercial Facility Savings (12 Hrs/Day at $0.13/kWh)
Operating 12 hours per day, 365 days per year (4,380 hours/yr):
- Per-Lamp / Per-Fixture Savings: Cuts 558 kWh/year, saving $72.60/year per unit.
- 25-Unit Facility Upgrade: Retrofitting 25 units reduces annual utility bills by $1814.96/year.
- Reduced Lift & Relamping Labor: High-bay, pole, and canopy fixtures often require scissor-lift or bucket-truck service calls. A 50,000+ hour LED rating eliminates multiple relamping and ballast-replacement cycles.
- Instant Outage Recovery: HPS lamps need ~1 minute to cool before restriking and several minutes to reach full output; LEDs return at 100% brightness immediately.
4. Primary Applications for 150W High-Pressure Sodium Retrofits
Commonly installed in residential and collector streets (cobra-head fixtures), farm yard poles, parking areas, and building wall packs. Physical lamp specification: ED23½ (S55 lamps) or ED28 (S56 lamps) bulb, most often with an E39 mogul base.
System draw falls from about 190W to 50–75W (~9,000 delivered white lumens), and the LED reaches full brightness instantly instead of warming up over several minutes.
HPS ignitors are a frequent failure point that causes cycling ("blinking on and off") — a Type B bypass or new LED fixture eliminates both the ignitor and ballast.
Quick Reference: 150W HPS Lamp vs. LED Replacement
| Spec | 150W HPS lamp | LED replacement |
|---|---|---|
| ANSI ballast code | S55 (55V) or S56 (100V) | None (ballast removed / new fixture) |
| Bulb & base | ED23½ (S55 lamps) or ED28 (S56 lamps) bulb, most often with an E39 mogul base | Type B corn bulb or integrated LED fixture |
| Light output | 16,000 initial / 14,400 mean bare-lamp lm | ~9,000 delivered lm |
| Power at the meter | ~190W including ballast | 50–75W |
| Color | ~2,000–2,100K amber, CRI ~20–22 | 2700K–5000K white, CRI 70–80+ |
| Rated life | 24,000+ hours | 50,000+ hours (L70), typical |
| Warm-up / restrike | Several minutes warm-up / ~1 min restrike | Instant |
What's Specific to the 150W HPS Retrofit
Two incompatible 150W HPS lamps
150W HPS was sold in two incompatible electrical standards: ANSI S55 (55-volt arc) and ANSI S56 (100-volt arc). With a Type B LED conversion or full fixture replacement, the ballast is removed and that mismatch disappears.
Cobra heads and barn lights favor full fixture swaps
In horizontal cobra-head street fixtures and open yard lights, corn bulbs lose a large share of light against the upper housing. Replacing the head with a 50–75W integrated LED roadway or dusk-to-dawn barn light puts more usable light on the ground per watt.
Color temperature for streets and yards
Follow the AMA's 3000K-or-lower guidance near homes and bedrooms; use 4000K in commercial loading or parking areas where camera color contrast takes priority.
Sizing From Delivered Light (Worked Example)
Omnidirectional 150W HPS lamps lose roughly 30–35% of bare-lamp output inside the reflector housing, and broad-spectrum white LEDs (CRI 70–80+) achieve equivalent outdoor task visibility at lower raw lumens than 2100K amber sodium.
Example: targeting ~9,000 delivered lumens from an integrated LED luminaire operating at 140 lm/W requires roughly 65W — compared with ~190W on the existing 150W HPS ballast circuit. For critical roadways, sports poles, or high-bay aisles, verify spacing with the manufacturer's IES photometric file.
5. Commercial Installation: Type B Ballast-Bypass Protocol
When retrofitting an existing housing with a Type B (ballast-bypass) LED lamp rather than replacing the whole fixture:
- Lock Out Power: Shut off and lock out the branch circuit breaker at the panel, then verify zero voltage at the fixture.
- Bypass the Ballast: Disconnect incoming line and neutral leads from the old ballast (and disconnect any ignitor and capacitor — leaving an HID ignitor in circuit sends multi-kilovolt pulses that will destroy an LED driver).
- Check Sockets & Wire Direct: Connect line voltage (typically 120–277V) to the lamp socket leads per the LED manufacturer's wiring diagram.
- Apply the Retrofit Label: Place the included modification sticker inside the luminaire housing warning future technicians that the ballast has been bypassed and legacy High-Pressure Sodium lamps must not be installed.